Install Easycraft V-Joint Panels
Watch Kyal and Kara demonstrate just how easy it is to Install Easycraft V-Joint Panels
Install Easycraft V-Joint Panels
Easycraft V-Joint Panels in the main bathroom upstairs at Toowoon Bay
Install Easycraft V-Joint Panels
Create a coastal feel by pairing the panels with tiles
Install Easycraft V-Joint Panels
The main bedroom at Toowoon Bay features a wall of painted Easycraft V-Joint Panels
Install Easycraft V-Joint Panels
The panels come pre-primed and ready for painting
 
How To

Install Easycraft V-Joint Panels

Products You'll Need Products You'll Need

Tools You'll Need Tools You'll Need

  • Tape measure
  • 1200mm Level 
  • Pencil 
  • Nail Gun or Hammer 
  • Power Saw or Timber Handsaw 
  • Personal Protective Equipment 
  • Chisel or Wide Flat Bladed Screwdriver 
  • Caulking Gun
 
Step 1

Planning & Preparation

 

Work out how many sheets you’ll need by dividing the length of your wall by 1200mm (the width of the sheet). Don’t forget to measure the height of your wall as well.Have all your tools set out ready to go and a clear area to work in.I would also recommend removing your skirting board so that the sheet can go down past the top of your skirting board and can be re-fitted once you have completed the paneling on your wall

The first sheet is the most important sheet to get right. Make sure it's plumb (perfectly vertical). Use your 1200mm level to do this. This will make the whole process run smoothly.

Step 2

Marking your First Sheet 

 

Firstly, workout the length and height of your first sheet. To do this, measure from floor to the under side of cornice, and then subtract 10mm - this will then be the size you will cut your sheet. Once you have your sheet cut, take it for a dry run! Meaning fit the sheet to the wall before you go getting glue everywhere. If you’re happy with how it fits, head to step 3. If you notice a gap at the top of your cornice you can scribe it to fit neatly.

 

Step 3

Glue Up 

 

Now that you have your sheet cut and ready to go, it’s time to glue up the wall using the acrylic stud adhesive. You want to make sure you do dab’s of glue about the size of a 20c piece and space the glue dab’s roughly 300mm apart. Only glue the space where the sheet is to be fitted.

 

Step 4

Install First Sheet  

 

Fit the sheet to wall and give it a solid pat ensuring it's nice and flat against the wall. You may need to level the sheet using a chisel and hammer to leaver the sheet up tight to your cornice. Once you are confident that it’s level you can nail off the sheet.

 

Step 5

The Next Few Sheets 

 

Again measure the height of your sheet and cut. Take it for a dry run and make any adjustments needed for a tight fit to your cornice! Once you’ve done this its time to glue up and fit your sheet to the wall. At this point you want to make sure you get your join perfect with the other sheet. Push the sheets together joining the groove into the joining strip. The join should now be concealed leaving no gap. Once you’re satisfied with this nail the sheet off and repeat this step until you reach your last sheet.

 

 

Step 6

The Final Sheet 

 

Measure the distance from the wall to the last sheet you installed. It’s a good idea take a measurement from the bottom and the top incase the wall your butting into runs out. Transfer the measurements onto your last sheet and cut. Dry run, make adjusting cuts if needed, glue up, fit sheet in place, make sure join with other sheet is good then nail off.

 

Step 7

Finishing Off  

 

Now all your sheets are installed its time to finish up and prep for paint! Fill all your nail holes with putty/timber filler. Give the filler some time to set then sand. If there are any gaps between cornice and sheet, or the internal wall and the sheet, simply gap fill with Selleys gap filler using your caulking gun. Re-fit your skirting board and get Painting. 

Vote for your favourite Long Jetty Reno Room for your chance to WIN a ‘Handcrafted Tasmanian Oak Children's House Bed’ valued at $1,690.



Please enter your reason
*Terms and conditions apply, Read competition details.